You are here: Home > Engine > Cylinder Head > Camshafts
Choose a sub category:
07K 2.5 5 cylinder 1.8T 12V VR6
24V 3.2 VR6 24V VR6
Sort By:
Page of 1
Cat Cams 7607220 for 12V VR6 Cat Cams 7607221 for 12V VR6 Cat Cams 7607225 for 12V VR6

7607220
sport
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 273
273
duration @ 1.0mm
: 234
234
valve lift
: 11.00mm
11.00mm
cam lift
:
lobe angle
: 120
110
timing @ 1.0mm
: -3 / 57
47 / 7
valve lift @ TDC
: 0.65mm
1.80mm
parts setup:
cam wheels :
:
:
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: O.E.M.
: O.E.M.
interior spring
: O.E.M.
: O.E.M.
fitted load / length
: 35kg @ 33.0mm
: 35kg @ 33.0mm
max. load / lift
: 86kg @ 11.0mm
: 86kg @ 11.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :


7607221
sport
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 285
285
duration @ 1.0mm
: 242
242
valve lift
: 11.05mm
11.05mm
cam lift
:
lobe angle
: 115
115
timing @ 1.0mm
: 6 / 56
56 / 6
valve lift @ TDC
: 1.70mm
1.65mm
parts setup:
cam wheels :
:
:
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: O.E.M.
: O.E.M.
interior spring
: O.E.M.
: O.E.M.
fitted load / length
: 35kg @ 33.0mm
: 35kg @ 33.0mm
max. load / lift
: 86kg @ 11.0mm
: 86kg @ 11.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift

7607225
turbo conversion
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 272
271
duration @ 1.0mm
: 233
225
valve lift
: 11.00mm
10.00mm
cam lift
:
lobe angle
: 120
114
timing @ 1.0mm
: -4 / 57
46 / -1
valve lift @ TDC
: 0.65mm
0.95mm
parts setup:
cam wheels :
: View TVW034
: View TVW034
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: O.E.M.
: O.E.M.
interior spring
: O.E.M.
: O.E.M.
fitted load / length
: 35kg @ 33.0mm
: 35kg @ 33.0mm
max. load / lift
: 86kg @ 11.0mm
: 86kg @ 11.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift

Cat Cams 7607222 for 12V VR6 Cat Cams 7607223 for 12V VR6 Cat Cams 7607224 for 12V VR6

7607222
sport
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 283
283
duration @ 1.0mm
: 242
242
valve lift
: 11.55mm
11.55mm
cam lift
:
lobe angle
: 116
108
timing @ 1.0mm
: 5 / 57
49 / 13
valve lift @ TDC
: 1.55mm
2.65mm
parts setup:
cam wheels :
:
:
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
ECU reprogramming required
7607223
hot street - dirt track
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 288
288
duration @ 1.0mm
: 249
249
valve lift
: 12.00mm
12.00mm
cam lift
:
lobe angle
: 112
108
timing @ 1.0mm
: 12 / 57
52 / 17
valve lift @ TDC
: 2.60mm
3.15mm
parts setup:
cam wheels :
:
:
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
stand alone ECU based on throttle position sensor required


7607224
tarmac rally - race
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 298
298
duration @ 1.0mm
: 258
258
valve lift
: 12.50mm
12.50mm
cam lift
:
lobe angle
: 108
108
timing @ 1.0mm
: 21 / 57
57 / 21
valve lift @ TDC
: 3.75mm
3.75mm
parts setup:
cam wheels :
:
:
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
stand alone ECU based on throttle position sensor required

Cat Cams 7607226 for 12V VR6 Cat Cams 7607312 for 12V VR6 Cat Cams 7607313 for 12V VR6

7607226
turbo conversion
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 288
285
duration @ 1.0mm
: 249
242
valve lift
: 12.00mm
11.05mm
cam lift
:
lobe angle
: 120
114
timing @ 1.0mm
: 4 / 65
55 / 7
valve lift @ TDC
: 1.50mm
1.80mm
parts setup:
cam wheels :
: View TVW034
: View TVW034
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
for TURBO conversion (atmospheric to turbo)
#
stand alone ECU based on throttle position sensor required


7607312
tarmac rally - race
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: 0.25mm
0.25mm
duration @ 0.1mm
: 301
301
duration @ 1.0mm
: 254
254
valve lift
: 12.50mm
12.50mm
cam lift
:
lobe angle
: 108
108
timing @ 1.0mm
: 19 / 55
55 / 19
valve lift @ TDC
: 3.65mm
3.65mm
parts setup:
cam wheels :
: View TVW034
:
follower
: View CC005
: View CC005
valve lash
: View TS102
: View TS102
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
- valve clearance is to be adjusted using mechanical lash caps
-
please make sure that the lash cap does not touch the valve locks !
#
stand alone ECU based on throttle position sensor required


7607313
tarmac rally - race
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: 0.25mm
0.25mm
duration @ 0.1mm
: 305
305
duration @ 1.0mm
: 262
262
valve lift
: 13.00mm
13.00mm
cam lift
:
lobe angle
: 106
106
timing @ 1.0mm
: 25 / 57
57 / 25
valve lift @ TDC
: 4.40mm
4.40mm
parts setup:
cam wheels :
: View TVW034
: View TVW034
follower
: View CC005
: View CC005
valve lash
: View TS102
: View TS102
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
- valve clearance is to be adjusted using mechanical lash caps
-
please make sure that the lash cap does not touch the valve locks !
#
stand alone ECU based on throttle position sensor required

Cat Cams 7607314 for 12V VR6 Cat Cams 7607326 for 12V VR6 Cat Cams 7607311 for 12V VR6

7607314
tarmac rally - race
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: 0.25mm
0.25mm
duration @ 0.1mm
: 317
317
duration @ 1.0mm
: 270
270
valve lift
: 13.50mm
13.50mm
cam lift
:
lobe angle
: 106
106
timing @ 1.0mm
: 29 / 61
61 / 29
valve lift @ TDC
: 4.95mm
4.95mm
parts setup:
cam wheels :
: View TVW034
: View TVW034
follower
: View CC005
: View CC005
valve lash
: View TS102
: View TS102
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
- valve clearance is to be adjusted using mechanical lash caps
-
please make sure that the lash cap does not touch the valve locks !
#
stand alone ECU based on throttle position sensor required

7607326
turbo conversion
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: 0.25mm
0.25mm
duration @ 0.1mm
: 295
284
duration @ 1.0mm
: 250
238
valve lift
: 12.00mm
11.50mm
cam lift
:
lobe angle
: 120
114
timing @ 1.0mm
: 5 / 65
53 / 5
valve lift @ TDC
: 1.80mm
1.80mm
parts setup:
cam wheels :
: View TVW034
: View TVW034
follower
: View CC005
: View CC005
valve lash
: View TS102
: View TS102
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
stand alone ECU based on throttle position sensor required

7607311
tarmac rally - race
Volkswagen AAA
VR-6cyl 2.8L 12v DOHC (DTH/DTH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: 0.25mm
0.25mm
duration @ 0.1mm
: 293
293
duration @ 1.0mm
: 246
246
valve lift
: 12.00mm
12.00mm
cam lift
:
lobe angle
: 112
108
timing @ 1.0mm
: 11 / 55
51 / 15
valve lift @ TDC
: 2.60mm
3.15mm
parts setup:
cam wheels :
: View TVW034
: View TVW034
follower
: View CC005
: View CC005
valve lash
: View TS102
: View TS102
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: O.E.M.
: O.E.M.
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-E99860
: View PAC-E99860
interior spring
: View PAC-I99860
: View PAC-I99860
fitted load / length
: 31kg @ 33.0mm
: 31kg @ 33.0mm
max. load / lift
: 99kg @ 13.0mm
: 99kg @ 13.0mm
REMARKS :
#
check interference between valve seal and retainer over 10,5mm lift
REMARKS :
#
FOR COMPETITION APPLICATIONS ONLY. Following details must be verified:
-
the camshafs must turn smooth in the cylinderhead, provide free travel by machining where needed
-
distance between valve seal and retainer at full lift must be 0.6mm at least
-
minimum valve spring travel of 1.0mm at full lift must be provided
-
distance between valve and piston 1.0mm (pref. 1.5mm). check 5-15 before TDC on exhaust, and after TDC on intake
#
- valve clearance is to be adjusted using mechanical lash caps
-
please make sure that the lash cap does not touch the valve locks !
#
stand alone ECU based on throttle position sensor required

Cat Cams 3658 For 1.8T Cat Cams 3652 For 1.8T Cat Cams 7607423
Cat Cams 3658 For 1.8T
Our Price: $675.99
Cat Cams 3652 For 1.8T
Our Price: $675.99
Cat Cams 7607423
Our Price: $889.99

Duration: 268 / 263
Maximum Lift: 9.25 / 9.95mm
Lift At TDC: 1.30 / 0.95mm
Hydraulic Lifter
7607423
hot street - dirt track
Volkswagen BDE 150kw, dual VVT
VR-6cyl 2.8L 24v DOHC (RPRH/RPRH)
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
: hydro
duration @ 0.1mm
: 280 - 276
: 268 - 272
duration @ 1.0mm
: 233 - 229
: 221 - 225
valve lift
: 12.00mm
: 11.50mm
cam lift
: 5.95mm
: 5.75mm
lobe angle
: 130-128
(78-76)
: 106-108
(128-130)
timing @ 1.0mm
: -14/67 - -14/63
: 36/5 - 40/5
valve lift @ TDC
: 0.15-0.15mm (6.25-6.35)
: 1.50-1.50mm (0.20-0.20)
parts setup:
cam wheels :
:
:
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: View 99312/H
: View 99312/H
lower retainer
: O.E.M.
: O.E.M.
exterior spring
: View PAC-S90015
: View PAC-S90015
interior spring
fitted load / length
: 30kg @ 38.0mm
: 30kg @ 38.0mm
max. load / lift
: 79kg @ 13.0mm
: 79kg @ 13.0mm
REMARKS :
#
springs can be fitted directly on cylinderhead, use solid shims to adjust spring load if required
#
double spring PAC-D19864 recommended over 8000rpm (in combination with upper retainer 99391/s and lower retainer 99537). Check valve seal clearance.
#
valve seal needs to be lowered for valve lift >11.0mm
REMARKS :
#
- camshafts for use in BDE (2.8L) engines with VVT sprocket on intake and exhaust
- ONLY for replacement of OE part number combination "022 109 102A" (intake) + "022 109 101C" (exhaust)
- camshaft installation position: intake at full retard / exhaust at full retard
- front cylinders (2-4-6) have long duration intake / short duration exhaust profiles
- rear cylinders (1-3-5) have short duration intake / long duration exhaust profiles
#
This is a very complex engine. The camshafts should only be fitted by experienced professionals who have the tools, skills and patience for correct installation, verification and adjustment of the timing events and all related parts.
#
stand alone ECU based on throttle position sensor advised
#
- intake valve: 1.8mm extra opening at TDC
-
exhaust valve: 1.2mm extra opening at TDC
CAREFULLY CHECK VALVE TO PISTON CLEARANCE

7604002
7604002
Our Price: $981.99

7604002
hot street - dirt track
Volkswagen CBT,CBU 170hp (07K) vvt in
I-5cyl 2.5L 20v DOHC
Save to PDF
intake
exhaust
camshaft data:
lash ramp
: hydro
hydro
duration @ 0.1mm
: 279
271
duration @ 1.0mm
: 233
225
valve lift
: 11.75mm
11.00mm
cam lift
: 6.95mm
6.55mm
lobe angle
: 127 (84)
111
timing @ 1.0mm
: -11 / 64
43 / 2
valve lift @ TDC
: 0.25mm (5.35mm)
1.15mm
parts setup:
cam wheels :
:
:
follower
: O.E.M.
: O.E.M.
valve lash
: O.E.M.
: O.E.M.
valve
: O.E.M.
: O.E.M.
valve locks
: O.E.M.
: O.E.M.
upper retainer
: View 99545/s
: View 99545/s
lower retainer
: View 99546/O
: View 99546/O
exterior spring
: View PAC-E99865
: View PAC-E99865
interior spring
: View PAC-I99865
: View PAC-I99865
fitted load / length
: 35kg @ 29.5mm
: 37kg @ 28.9mm
max. load / lift
: 86kg @ 12.0mm
: 86kg @ 11.4mm
REMARKS :
REMARKS :
#
Distance between valve and piston should be 1.0mm at least:
-
check 5-15 after TDC on intake
-
check 5-15 before TDC on exhaust
Machine pistons if required. Wrong installation can cause severe engine damage!
#
ONLY for dirt track applications and pro street use with adjustable engine management or carburettors