Credit Card Merchant Services


>

Enter Your Email To Sign Up
For Our E-Newsletter:


You are here: Home > Billet Accesories
Choose a sub category:
1.8T 12V VR6
2.0T FSI 24V/R32
Sort By:
Page of 1
Integrated Engineering -6an Coolant Adapter Fitting
Integrated Engineering -6an Coolant Adapter Fitting
List Price: $24.99
Our Price: $17.99
Save $7.00!

This coolant adapter fitting will allow you to use a factory coolant temp sensor location to plumb a -6an line for your water cooled turbocharger, or anything else you need coolant for. These are made to clip into the factory coolant temp sensor port used on MANY VW/Audi applications.

Features:
Made from 6061 aluminum
Male -6an outlet
Integrated Engineering M12x1.5 Coolant Temp Sensor Adapter
Integrated Engineering M12x1.5 Coolant Temp Sensor Adapter
List Price: $24.99
Our Price: $17.99
Save $7.00!

When installing a standalone ECU, finding a location for your coolant temperature sensor can be a bit tricky. We have designed these adapter bungs to clip into the factory VW/Audi coolant temperature sensor location, for a painless installation. These are tapped with M12x1.5 threads, which are commonly found on GM, Delphi, and some Bosch coolant temperature sensors.

Features:
Fits MANY VW/Audi engines
Uses Delphi sensor #TS10076 or equivalent

A must for standalone ECU users.
Billet Aluminum Breather Adapter for 1.8T, MK4 2.0L
Billet Aluminum Breather Adapter for 1.8T, MK4 2.0L
List Price: $42.99
Our Price: $32.99
Save $10.00!

Are you tired of the stock plastic crankcase breather hose always breaking? We have the solution for you! Stevebilt is proud to offer Integrated Engineering's Billet Aluminum Breather Adapter. This nifty little piece fits nicely into the factory bung for the crankcase breather. It features a -10an o-ring threaded port, so you can easily run a braided line, or simply push-lock lines and fittings.

These are a must for anyone looking to build a custom breather setup, or if you just want a bulletproof solution.

Features:
High quality billet aluminum construction
-10an o-ring threaded port
Red anodized finish

Will fit ALL VW 1.8T, and MK4 2.0L engines!

Priced individually
IE 2.5l 5 Cylinder SAI Blockoff Plate Kit
IE 2.5l 5 Cylinder SAI Blockoff Plate Kit
List Price: $79.99
Our Price: $47.99
Save $32.00!

Stevebilt is proud to offer Integrated Engineering's 2.5L 5cyl SAI Block-off Plates. These plates allow the removal of the entire secondary air injection / combi-valve system, including the large injection pump near the oil filter. This results in a much cleaner looking engine bay, as well as less clutter and more room for you to get in there and wrench on your ride. These plates are CNC machined from 6061 aluminum alloy, as well as machined to accept an O ring seal, so they seal up perfectly with no fuss, and no gaskets or messy sealant. The installation is completed with the included aerospace grade Viton O ring, and stainless steel socket head hardware.

Available in red anodized finish only.

This is a complete kit, which includes both blockoff plates, o rings, and mounting hardware!

Note about check engine lights: There are two codes which may come up for this, one can be solved by adding a resistor to the circuit for the solenoid control valve, the other- for "incorrect flow detected" can only be defeated by software!

Integrated Engineering Valve Cover Breather Adapter 2.0T FSI
Integrated Engineering Valve Cover Breather Adapter 2.0T FSI
List Price: $129.99
Our Price: $97.99
Save $32.00!

Integrated Engineering has a solution for the PCV valve that commonly fails on the 2.0T FSI engines. These beautiful billet pieces are a direct replacement for the faulty plastic pieces that cause rough idle, check engine lights, power loss and decreased fuel economy. This will eliminate the factory PCV valve.This adapter comes pre-assembled with the required barb to clip the factory block breather hose to. Unlike other pieces available, this piece maintains the two breather outlets for proper crankcase ventilation. These can easily be plumbed to a catch can to collect the oil mist that is emitted.

Features:
Direct fit for all 2.0T FSI engines
Made in house from 6061 aluminum
Two -10an O-ring boss outlets for catch can
Integrated Engineering External Oil Cooler Adapter Plate Kit for 2.5L 5 Cylinder
Integrated Engineering External Oil Cooler Adapter Plate Kit for 2.5L 5 Cylinder
List Price: $129.99
Our Price: $99.99
Save $30.00!

Stevebilt is proud to offer Integrated Engineering's external oil cooler adapter plate for your MK5 2.5L 5 cylinder engine. This kit will allow you to remove your factory oil cooler and replace it with a more efficient external oil cooler. These are a direct fit onto the OEM oil filter housing using the included stainless steel mounting bolts. These billet adapter plates are made in house by IE from 6061 aluminum, and completed with a red anodized finish. The inlet/outlet holes on the plate are tapped for -8an o-ring boss fittings. Take care of your oil temps today with this quality piece!

Includes stainless mounting bolts, and 2 -8an adapter fittings.
   
 

Copyright ©  www.sbpartsdirect.com. All Rights Reserved. Built with Volusion